Leading 10 common forklift mishaps ， forklift operation should take note of these matters ！.

Don't undervalue the forklift at the office. If the procedure is bad, there will certainly be significant mishaps in mins, and there are several crashes involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a tons, the vehicle driver must initially verify that the lots is steady and reliable.
4. The beginning must be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal must be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when piling or filling. .
8. The elevation of the lots need to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks ought to be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the thing ought to be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the tons, and it needs to be noted that the fork idea should not touch other items or objects. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not glide in reverse. The mast can be slanted ahead a little when the tons is decreased to allow for very easy positioning of the load and removal of the forks. .
6. It is prohibited to fork products at high speed and hit tough items with the fork head. .
7. When the forklift is functioning, it is prohibited for individuals to loaf the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overwhelming is prohibited, and it is restricted to make use of forks to lift workers to take part in high-altitude operations to avoid high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and move on, if they come across large or heavy items and most likely to the chauffeur's line of sight, they need to take the turning around workout
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Single fork operation is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab Stand-on Electric Pallet Stacker the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Parking Stand-on Electric Pallet Stacker is not permitted under the following problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844